Abdullah Saeed Almrri
Madina
Summary
An Mechanical Maintenance Engineer with a Bachelor Degree In Mechanical Engineering Technology. I have 2+ experience in Maintenance , Utilities , and Facilities field . Excellent background in Reporting, Identifie issues, analyzed information and provided solutions to problems , calculation of equipment operating efficiency per month with expertise in asset management , and maintain it . As well as familiarity with Maximo ,SAP, Microsoft Office, and MS Project.
Overview
2
2
years of professional experience
3
3
Certifications
1
1
Language
Work History
Mechanical Maintenance Engineer
King Faisal Specialist Hospital and Research Centre
03.2021 - Current
- Planned Preventive Maintenance for Chillers Units : 1
- Check the condenser coils if found any debris remove and clean the coils with appropriate chemical Coil cleaner
- 2
- Check the moisture indicating sight glass and charge freon if needed 3
- Check all refrigerant joints and repair if any leakage of freon 4
- Check oil sensor , cooler sensor , compressor motor temperature sensor operation 5
- Check the water flow switch operation and clean the steam strips 6
- Check suction and discharge pressure of Rerigerants with gas manifold guage and compare with readings on display module so that proper operational confirmation of each pressure tranducer 7
- Check and locate position of the atmospheric temperature sensor away from heating components
- Inorder to get accurate atmospheric temperature
- 8
- Check all setpoint paremeters in display module and compare with actual If applicable 9
- Check the cooler heater operation , voltage , ampare, and tighen the jack connections 10
- Check the pressure gauges in chilled water inlet and outlet
- If malfunctioned or damage replace
- Planned Preventive Maintenance for Boilers Units : 1
- Inspect burner 2
- Inspect for flue gas leak 3
- Inspect for hot spots 4
- Check cams 5
- Check for tight closing of fuel valve 6
- Check fuel and air linkage 7
- Submission the Service report for each visit 8
- Check indicating lights and alarms
- 9
- Check operating and limit controls
- 10
- Check safety and interlock controls
- Planned Preventive Maintenance for 3 Boilers Feed Pumps , 3 Diesel Pumps , 8 Secondary Pumps , 5
- Primary Pumps, 6 Domestic Pumps , 6 Treated Pumps , and 4 Housing Pumps : 1
- Carry out visual check of unit to ensure it is functioning correctly
- 2
- Inspect unit for undue noise , vibration and corrosion
- 3
- Check for water leaks
- 4
- Clean pumps externally with an air blower / cloth
- 5
- Check for any leakage in oil and gas system repaired as required and top upon completion of remedial works
- 6
- Check and record suction and discharge pressure
- 7
- Record Suction Chilled Water Pressure
- 8
- Record Discharge Chilled Water Pressure
- Planned Preventive Maintenance for Generators Units : 1
- To inspect the machines and check for any leaks and calibrate them
- 2
- To test the operation of the oil heaters and check the operation of the lubrication circuit and ensure that there is no leakage in it
- 3
- To check the water cooling circuit and making sure that there is no leakage in it
- 4
- To inspect the fuel circuit and making sure that there is no leakage in it
- 5
- To test the work of the distribution boards and ensure that they work normally
- 6
- To inspecting the movement belts , couplings , chairs and rotating parts and ensuring that they are in good condition
- 7
- To test the battery charger to ensure that it is working properly and normally
- 8
- To check the water level in the batteries and the concentration of the solution To perform machine vibration test
- 9
- To perform machine vibration test
- 10
- To ensure that the impurities are darined from the outside air tanks
- 11
- To operate the generator on load , recording , inspection and comparing the generator readings 12
- (pressure and cylinder temperature )
- 13
- To test the work of all pumps and ensure their suitability to operate normally 14
- To inspect the exhaust circuit and making sure that there are no leaks in it or in the flexible joints
- 15
- To inspect the ventilation ducts of the machine and making sure that they are clean
- 16
- To check the external oil coolers and making sure that all cooling fans are working in good condition
- 17
- To test all protection and alarm devices in the electrical circuit and ensure their safety and suitability for work
- 18
- To inspect the distribution cables as well as all their connections and ensuring their safety
- 19
- Inspecting the distribution boards as well as all their connections and ensuring their safety
- 20
- It is necessary to conduct calibration work for the entire system
- 21
- To operate the generator on load for four hours , taking into account that the disconnection and connection are done automatically
- 22
- To inspect the axle chairs pulleys and water pumps
- 23
- To check the water filters and cleaning the water cooling circuit completely clean
- 24
- To inspect the air filters and cleaning the air circuit
- 25
- To inspect of all connections and coils of basic generators
- 26
- To measure the resistance of the generator windings and ensure that they comply with the manufacturer's instructions
- 27
- To test and calibrate all measuring devices in the distribution panels according to the manufacturer's instructions
- 28
- To inspect the main fuel tank and ensure its safety and validity
- 29
- To check the generator protections against overspending
- 30
- To check the generator protections against the high temperature of the cooling water
- 31
- Inspect and test the voltage regulator , calibrate the gauges , check the cable end connections and generator main contactors , and remove any carbon buildup
- 32
- Inspect the fuel pumps , turbocharger , speed governor and adjust when needed .
Education
Bachelor’s degree - Mechanical Engineering
Jeddah College Of Technology
Skills
1 Leadership & Team Building2 Fixability and ability to manage priorities3 Teamwork4 Work under pressure5 Microsoft Office Skills (Excel, Word, PowerPoint)6 Ability to solve problems7 Achievement Focus8 Time Management9 Solid Works10 AutoCad11 Maximo
Certification
OSHA Academy Safety and Health Training
Timeline
Mechanical Maintenance Engineer
King Faisal Specialist Hospital and Research Centre
03.2021 - Current
Bachelor’s degree - Mechanical Engineering
Jeddah College Of Technology